Rabbit-Labs PermaMark™ RL Classic Logo

# Rabbit-Labs PermaMark™ RL Classic Logo Decal — ## ▌PRODUCT DESCRIPTION **>> THE ORIGINAL MARK. NO COLOR. NO COMPROMISE. <<** Before the prismatic gradients. Before the ChromeRabbit™. There was this. The **Rabbit-Labs PermaMark™ RL Classic Logo** is the original Rabbit-Labs rabbit rendered in its purest form: **solid black, clean detail lines, zero background**. This is the logo stripped down to its bones. Bold. Minimal. Unmistakable. If you know, you know. If you don’t, you will. This premium transfer decal is engineered to bond to damn near any hard, smooth surface and stay there. Glass. Metal. Ceramic. Plastic. Polycarbonate laptop shells. Powder-coated cases. Pelican lids. Toolboxes. Tumblers. If it’s solid and smooth, the RL Classic locks on. **UV-proof and water-resistant.** Rated for prolonged outdoor exposure without fading, cracking, peeling, or yellowing. Sun, rain, sleet, humidity. The RL Classic doesn’t care. It holds. **Precision die-cut to the exact contour of the rabbit silhouette.** No rectangle. No visible background. No white border. No carrier material left behind. Just the black rabbit with clean edges, flush against whatever surface you chose, looking like it was always part of the hardware. The monochrome black finish works on everything. Light surfaces, dark surfaces, brushed metal, matte plastic, glossy enamel. Where the ChromeRabbit™ demands attention with color, the RL Classic earns it with contrast and simplicity. Mark your gear. Keep it clean. **Run silent.** FLIPPER FOR SCALE – NOT INCLUDED! — ## ▌README.TXT – APPLICATION INSTRUCTIONS **Before you begin:** Ensure your target surface is clean, dry, and free of dust, oil, or residue. Isopropyl alcohol (90% ) and a lint-free cloth are recommended for surface prep. Ambient temperature should be above 50°F / 10°C for optimal adhesion. **Step 1: Separate** Carefully peel the decal transfer sheet away from the paper backing. The decal graphic will remain adhered to the clear transfer film. **Step 2: Position & Apply** Place the transfer film (decal side down) onto your target surface. Start from one edge and slowly lay it down to minimize trapped air bubbles. *You get one shot at placement. Reposition carefully before pressing down.* **Step 3: Burnish** Using the edge of a credit card, gift card, or similar flat tool, firmly smooth over the entire decal from the center outward. Apply even, firm pressure. This bonds the graphic to the surface and forces out any remaining air. **Step 4: Peel & Reveal** Slowly peel the clear transfer film away at a sharp angle (close to 180°). Pull *low and slow*. Not straight up. If any part of the decal lifts with the film, press it back down, re-burnish that area, and try again. **Step 5: Final Press** Once the transfer film is removed, go over the decal one more time with your card edge to ensure full contact and edge adhesion. > **PRO TIP:** For curved surfaces (tumblers, bottles, helmets), a brief pass with a heat gun or hair dryer on low *after* application helps the adhesive fully conform and lock in. — ## ▌DEBUG LOG – TROUBLESHOOTING **ISSUE: Air bubbles trapped under the decal.** FIX: Use a pin or fine needle to puncture the bubble at its edge, then smooth toward the puncture with a card to evacuate the trapped air. Small bubbles (<2mm) typically self-resolve within 24-48 hours. **ISSUE: Decal lifts off the surface when removing transfer film.** FIX: The decal hasn’t fully bonded. Press the film back down, re-burnish with firm pressure, and wait 2-5 minutes before attempting removal again. On porous or textured surfaces, additional burnishing time may be required. **ISSUE: Edges are peeling or curling after application.** FIX: Surface may have had residual oil, dust, or moisture. Clean the exposed area around the lifted edge with isopropyl alcohol, press the edge back down, and burnish firmly. If the edge won’t re-adhere, a tiny drop of clear adhesive (e.g., Loctite Vinyl/Fabric/Plastic adhesive) can be applied under the lifted portion. **ISSUE: Decal won’t adhere to the surface at all.** FIX: Some surfaces resist adhesion: silicone, unsealed raw wood, heavily textured/matte finishes, oily or waxy coatings, and flexible/soft rubber. This decal is designed for **hard, smooth, non-porous surfaces**. Ensure the surface is thoroughly cleaned and dried before retrying. **ISSUE: White detail lines appear faded or incomplete.** FIX: The white lines in the RL Classic design are fine details. If they appear broken or missing on arrival, this may indicate a production defect. Contact Rabbit-Labs support for a replacement. Do not apply a defective decal. — ## ▌SYS.WARN – WARNINGS, HAZARDS & DISCLAIMERS **Surface Compatibility:** This decal is engineered for hard, smooth, non-porous surfaces. Application to fabric, leather, skin, silicone, unsealed wood, or heavily textured surfaces is not recommended and may result in poor adhesion or decal damage. Rabbit-Labs LLC is not responsible for unsatisfactory results on incompatible surfaces. **Semi-Permanent Application:** This is a **semi-permanent** decal. While it can be removed, removal may leave adhesive residue and could potentially damage delicate surface finishes (e.g., matte coatings, soft-touch plastics, painted surfaces, vehicle clear coat). Test in an inconspicuous area first if surface damage is a concern. Rabbit-Labs LLC is not liable for damage to surfaces resulting from application or removal of this product. **Placement Responsibility:** The end user is solely responsible for where this decal is applied. Do not apply to surfaces you do not own, surfaces where adhesive application is prohibited, or any government, municipal, or private property without authorization. Rabbit-Labs LLC does not condone vandalism or defacement of property. **Not a Toy:** This product contains small components (backing sheet, transfer film) that may pose a choking hazard for small children. Keep out of reach of children under 3 years of age. **Storage:** Store in a cool, dry location away from direct sunlight prior to application. Prolonged pre-application UV exposure may degrade adhesive performance. **Disclaimer:** This product is sold “as-is” for decorative purposes only. While designed for UV and water resistance, long-term durability may vary based on environmental conditions, surface material, and application technique. Rabbit-Labs LLC makes no warranty, express or implied, regarding fitness for a particular purpose. Maximum liability shall not exceed the purchase price of the product. — *© Rabbit-Labs LLC. All rights reserved. The Rabbit-Labs name and logo are registered trademarks of Rabbit-Labs LLC.*